Sabine Marcelis – Column Instructions

Contents
Column comes packaged in a single large box.

Base Assembly, 150W R7s Bulb, Top Cap & Filled Bottle

Position
Column is for indoor use only. Choose your position carefully, especially if Column is to be used in public areas. Ensure that the cable can reach the power socket location without being stretched and does not become a trip hazard. Choose a position on a robust flat surface able to bear its weight. Column operates at its best in a room between 20º C / 68º F and 24ºC / 75º F.
For best performance we recommend you keep the product away from:

• sunlight to prevent fading
• drafts and cold places, such as an air conditioner, to prevent slow operation and freezing
• hot places, such as a heater, to prevent overheating.

Assembly
For a full visual guidance recommend you watch the video which can be found on the Column page on the Mathmos website.
The Base

1. Open the box and carefully take out the Top Cap and Base
2. Place the lamp in position.
3. Fit the bulb into the product by pushing one end in and springing it into place between the lamp holder contacts. (diagram 1). Ensure that each end of the bulb is sitting correctly in the lamp holder.

The Base

1. Open the box and carefully take out the Top Cap and Base
2. Place the lamp in position.
3. Fit the bulb into the product by pushing one end in and springing it into place between the lamp holder contacts. (diagram 1). Ensure that each end of the bulb is sitting correctly in the lamp holder.

The Bottle

1. Take great care removing the bottle from the box. It is both heavy and fragile.
2. Open the box by removing the tear off strip.
3. Open the flaps and remove the top cardboard insert and set this aside.
4. Using the handles on the side of the box, carefully lower the box so the long side is on the floor.
5. Place the cardboard insert set aside earlier in front of the box at the opening to protect the bottle as it comes
   out of the box.
6. Pull the bottle out of the box using the neck of the bottle and as you do this move the bottle upright to stand it
   on the insert. (diagram 2)
7. Slowly lift the bottle and then lower the bottle into position on the base, ensuring that it fits neatly into the
   base spinning. NB. The bottle is weighs approximately 23kg, this operation may require two people.
8. Fit the cap onto the top of the bottle.

Warm Up
Warm up takes between 4 to 5 hours depending on the ambient temperature. Stalagmite shapes may form during the warm
up process, these will then melt and the lava will begin to flow. You may want to use a timer with Column so that it turns on
automatically.

Operation
Column will operate best after it has been used four or five times. For the first few times you may see small air bubbles in
the lava. Column can run for up to 12 hours once warmed up (during one operating cycle). Please allow Column to fully cool
before running it again.

Do not allow Column to overheat as this will shorten the life of the lava. If it is overheating there will be either only one large
bubble at the top of the bottle or a lot of very small bubbles.

Never move the product when it is in use or still warm, as this causes irreparable clouding.
It is normal for the glass to have small air bubbles and moulding scars.

Replacements
When your Column has ended its life, it will begin to go cloudy, the colours may fade and it will not move as well as it once
did. This will happen after approximately 2000 hours in operation. Whether your product has ended its life or when you wish
to have an alternative colour combination, visit our website at www.mathmos.com for more information on a replacement
bottle or full product.

Please on no account open the secure cap and add liquids.

Changing the Lamp
Avoid handling bulbs with your bare hands, instead use a soft cloth or similar.

IMPORTANT! Always allow your product to cool down completely prior to handling or maintaining the product. Once your
product has completely cooled, carefully lift out the bottle from the base and set down on a sturdy surface safely away from
the base.

Fit the bulb into the product by pushing one end in and springing it into place between the lamp holder contacts. (diagram 1).
Ensure that each end of the bulb is sitting properly in the lamp holder.

If the bulb blows, please replace it with one of the same type and wattage. Only fit the correct bulb, as stated in the label in
the base. Visit our website at www.mathmos.com for more information on replacement bulbs.

Safety

• This product carries the statutory guarantee of the country of purchase and meets all the applicable
  standards requirements.
• This product is only suitable for connection to a 220 – 240V ~ 50Hz mains supply. It must only be fitted with a 3A
  fuse.
• If this is to be installed in a public space then we recommend fitting it to a RCD device.
• This fitting is a Class II, Double Insulated product and does not require an Earth.
• Place the product well away from children under 14 years to prevent breakage.
• Use this product only for its intended use as described in these instructions. Do not use attachments not
  recommended by the manufacturer.
• Do not use any other means to heat up the bottle other than the bulb provided nor attempt to cool it
  down artificially.
• Do not operate the product for more than 12 hours once warmed up (during one operating cycle).
• The liquids in the product are not dangerous and can be disposed of normally (for details, see our online
  FAQ’s at www.mathmos.com). If the liquid is swallowed by mistake, drink plenty of water. If any
  symptoms appear, please visit a doctor.
• Never use this product if the bottle has been dropped as this will create weakness; obtain a replacement
  bottle and dispose of the old one. If the contents are spilled please dispose of as much liquid and lava
  as you can remove, then use recommended cleaning methods for removing coloured water and wax for
  whatever floor you have.

To reduce the risk of burns, electric shock, or injury:

• Unplug from mains outlet before putting on or taking off parts or before cleaning.
• Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped
  or damaged, or if it has been submerged in water.
• The external flexible cable of this product cannot be replaced. If the cable is damaged, please contact
  Mathmos
• To disconnect, turn the switch to the off position, then remove plug from outlet.
• Never touch the bulb if the product is switched on or if it has just been switched off in order to avoid burning.
  To replace a defective bulb, unplug the product and let it cool down sufficiently.

NB. Mathmos Ltd. cannot be made liable for damage or injury caused by improper handling, installation or use of its
products.

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.